Infoseite // Rail Dolly makes problems! Ask for advice ..



Frage von Moritzk:


Since yesterday, I included a new camera car rails.
I have bought all over Ebay for 170 ¬.
Here's the link:

http://cgi.ebay.de/ws/eBayISAPI.dll?ViewItem&item=300398434094&ssPageName=STRK:MEWNX:IT

Sun has arrived yesterday and everything I was looking forward zuersteinmal :-) After unpacking, I then wanted to put all the tracks together ... that does not just walked!
In one of the rails, the connector is pressed into it and therefore I can no longer stick together. I've tried everything, but I get the connector simply pulled out.

Of course, I have written to the Ebayer same, only this could help me then not at all with his response ... here's Antort:

The connections are always connected by pins, which can be fastened with hex head screws. Perhaps one of the pins is slid to the inside. Maybe it helps to break through the side eien times with a rod, and again dan Tighten.
Love Greetings .......


Has anyone of you an idea how I get the connector pulled out again.
Attached Images as his was, and as with any of the tracks just is not.

Thank you very much,

lg Moritz

Space


Antwort von pilskopf:

Punctured from the other Page as he wrote does not work?

Space


Antwort von Moritzk:

"pilskopf" wrote: Punctured from the other Page as he wrote does not work?

I can not even push through because on the other so synonymous Page protrudes a connector to the outside ... and that I get no herraus drawn, but only 'pushed in. ... and when I do I have the same problem s.end both sides :-(

Space


Antwort von pilskopf:

And you're certain that not figure out are you? What are the inside of the Verhackt? What kind of a hole? Is not that something where you can Gradually tighten and then pull out the interior to be? Somehow that must have been put into it so afterwards, so you have to get it out again theoretically synonymous.

Space


Antwort von Moritzk:

"pilskopf" wrote: And you're certain that not figure out are you? What are the inside of the Verhackt? What kind of a hole? Is not that something where you can Gradually tighten and then pull out the interior to be? Somehow that must have been put into it so afterwards, so you have to get it out again theoretically synonymous.

But it is not simply works by pressing into it with ... I have already tasted synonymous, but this did not work out.
Vllt we must try even with brute force, but that I would not try it at first because I do not make ... kaput already bissl shit :-(

Space


Antwort von pilskopf:

The thing is needed, it might be slightly rusty, maybe because you can smear something, you probably need to apply Gewallt, stupid in any case, I'll buy on eBay nothing more, only new, because we know what we have.

Space


Antwort von Frank B.:

Since a hole in the rail, is obvious to a cotter pin or of you mentioned is meant to screw. The sapwood, however, is obviously not purely synonymous s.dem end, that you as "it must have to be described. So it should not be so. I think you have to bring the bolts that are in the tubes in the correct position that you can perform this screw / the sapwood. There must therefore be synonymous a hole in the bolt. This pin is split in the middle. I assume that he is under tension and so the inside of s.das tube is pressed. This is synonymous sense because it will not rattle in use. That suggests to me that the bolts must be agile, but they fit very tightly. I would advise you (subject to change times) a thick cloth or leather straps around the bolt, poking out of the still do, too. Then with a heavy pipe wrench, bolt pack them so that the gap is compressed and then try it. get out in a rotary motion. Maybe you need someone to help hold the rail (the tube). In any case, you should hook it clamped in a vise, since you damage it so with Schierheit, so that your Dolly then travels moguls. A strong man with a damp chamois leather should be able to hold the tube (do not laugh, I know that sounds really a bit ambivalent - but I do not know how to say it differently;)), wärend You s.Bolzen rotate the avatar. If you should get the pin out, you can next proceed as in the next post, it is said above. To go with a long rod through the tube rauszuschlagen and try the clamped pin. Before you can drop a little penetrating oil around the depressed pin.

Frank

Space


Antwort von Schleichmichel:

The connecting piece looks as if it would consist of two parts. Let squeeze these joints that? Then we could move through the gegend Splintöse that the connector is compressed and is therefore get popular.

If a hot air gun is present, then you can heat the pipe and then try to pull the part.

But drilling a hole (front s.dem connector) purely so you can pull it with a hook ...

Space


Antwort von Markus_Krippner:

Yes exactly ... Hole reinbohrn, Reinsch cut threads, reindrehen eye screw, and then pull out s.der screw. Possibly even bissle lubricate (with WD40).

That makes you any metalworking plant in 5 minutes.

The hole will not interfere with further use.

Maybe you could take the opportunity like all existing connectors can be fitted with a threaded hole, and you ne right eye bolt in your pocket with basket .... if that should happen then wiedermal.

markus ... :-)

Space



Space


Antwort von pilskopf:

It would take time for a Picture Moritz, is structured like this inside, so I'm assuming that works like an anchor, or am I mistaken?

Space


Antwort von B.DeKid:

Pull out the pin on the Richtigenseite as already mentioned with substances pass on and together with pipe wrench and Druecke.

Then broomstick through the tube and cause rausklopfen with the crushed rubber hammer nails. Before making nen bissel oil on it.

MfG
B. DeKid

Space





slashCAM nutzt Cookies zur Optimierung des Angebots, auch Cookies Dritter. Die Speicherung von Cookies kann in den Browsereinstellungen unterbunden werden. Mehr Informationen erhalten Sie in unserer Datenschutzerklärung. Mehr Infos Verstanden!
RSS Suche YouTube Facebook Twitter slashCAM-Slash