Frage von daylife99:
Have one s.meiner Panasonic HMC151 Rode NTG-2 and would like to spend the mic signal to both input channels of the camera (I already know is that not the stereo, I want only to simplify the video editing)
Have so far only 5 pin female XLR cable. found to 2x 3pin male. That is not so.
Is there a safe way for the camera, the signal is split up (phantom power)?
Switching scheme is enough for me, then I'm the cable itself.
Can the NTG-2 synonymous with Battery operated, only - as I then turn off the phantom power?
I'm grateful for any viable Tip
merci!
Antwort von beiti:
There should be no problem, zusammenzulöten parallel with a 1:1 wired adapter Fe_male of 1x XLR to 2x XLR Male. With the phantom power synonymous, it should be no problem, because the mic is so s.beiden outputs of the camcorder to the same, so that one here would risk a short circuit.
Whether one can then buy an adapter cable ready, I do not know. Most professionals are probably not interested in (or to the cutter) to simplify the post. ;)
PS: The word "female" was not the spam filter, the Forum accepts no trick. Strange ...
Antwort von beiti:
Look here:
http://www.thomann.de/de/cae_90074_yaudiosplittkabel.htm
Whether the cable length is sufficient for your purposes, I do not know.
Antwort von daylife99:
Thanks, the cable I've already found.
If, however, 5-pin input to 2x3polig output. That will help me with probably nix the 5-pole input, right?
lg
Peter
Antwort von beiti:
If, however, 5-pin input to 2x3polig output. No, it's 3-pin mikrofonseitig s.2x 3-pin camera side. What you just need to s.The one Rode NTG-2 Mic inputs connect your HMC-150th
That will help me with probably nix the 5-pole input, right? Which 5-pin input?
Antwort von beiti:
I just got the prospectus, the AG-HMC150 looked at. Since you can even turn the phantom power separately for both Bushes. If only s.einer activated tension, one can exclude a perfect electrical problems.
Switching scheme is enough for me, then I'm the cable itself. Simply Pin1 s.Pin1/Pin1, Pin2 s.Pin2/Pin2 and Pin3 s.Pin3/Pin3. For Pin1, take the shield, pin 2 and 3 for the inner conductor of the cable.
Antwort von daylife99:
5-pin? - The fe_male part has looked s.Picture 5 poles, hence my concerns. But has there aufelöst just because I've just phoned times at Thomann.
Although a bit short, the cable, but I had already lengthen.
Thanks for the hint.
LG
Peter
Antwort von beiti:
Although a bit short, the cable, but I had already lengthen. That's pointless. Then do it's just like yourself with the required cable length.
Antwort von daylife99:
it's true, but I do not have to shift pattern and in such cases I would rather be at home on the secure page. If it is so easy with Pin 1 to 2x pole one, etc. - then .... nix it. But it is so or do I have to cross there any poles? No clue. But I can solder ;-) (at least)
Antwort von beiti:
No, you have to cross any poles. XLR connectors have unique numbers that are always connected 1:1.
1: Ground
2: Hot Signal
3: Cold Signal
When you use this cable with two twisted Innenadern and shielding. Pin 1 (ground) is connected with the shield, pin 2 and 3 respectively with the inner conductors.
Antwort von daylife99:
Hurray!
This is really to create.
Thank me now (of course, synonymous of Geldbörserl ago) helped a lot. The "ingredients" are so easy to obtain.
Yes but I get up again and again on forums.
