oh oh terrible gruesome! For three days I have when shooting with my 1000 black bar across the Picture - the bars are horizontal - take a total of about 50% of the overall picture in the Picture, however (such as interlace) nice spread - always a bar image - then again, a black ...
Defective cartridges and Monitor had excluded me. Recording to other cartridges do not synonymous work.
The monitor - both as a viewfinder synonymous show off when playing beams of admissions (synonymous for the import of DV - Out).
Old tapes - and I mean old recordings - are ok!
When recording the picture in the viewfinder and external monitor in order.
More info: the bars are too green and some s.and Picture "fades" into the other (with a sort of "wipe" of the top left to bottom right, with many small squares motion artefacts). I hope someone understands me:)
I once type recording head in the bucket, right?
I hope you have a super tip for me: /
Greeting Sutt
Antwort von Maik:
Sutter "wrote:
I hope you have a super tip for me: /
My tip: small screwdriver, tweezers, cotton swabs and alcohol, and the drive Screw on and make a * rough * Cleaning. The side cover on the drive side goes off relatively easily, it is perhaps 2 handfuls of screws. The only thing that is a bit tricky: the handle above shall be synonymous unscrewed the back and then a little after at the top down (to free up the side cover there is a kind of Thorn of the side cover fixed).
Then the drive. In no case now with the cotton swab on the head rumwischen! I'll do it this way: with the tweezers I collect all the coarser out lint, Hang synonymous around the small foam that running with his head (as Sometimes the long right turn evil fluff, the active it such a Dreck ...) At the head itself, I'm nothing ... Whoever wipes, which makes more damage than anything else ... With the Q-Tip, I then clean the entire rest of the drive with alcohol. You see that already: s.den grippers and s.Tonkopf collects the place to be. If everything is clean, I pull all the screws slightly. Fittingly Screwdriver is required! And not too hard. Sometimes one or the other screw something resolved ... sowas can provide a false track position. Everything is back together and then the crowning glory: a cleaning cartridge Insert (I do not do that, for me it's not necessary, but in your Case, I would do it) and run a few seconds.
If all this has nothing helped, it was what you could do. More does not work, and the camera then has to service. My 1000 has now well over 1500 head hours, I clean it maybe once a year, according to the method. It still makes an impeccable picture ...
Have fun,
M.
Antwort von sutt:
Hi Maik,
let me briefly consider what I write now ...
Perhaps THANKS?
In fact, "schlapperte" the head and the screws could well attract a quarter turn.
5 minutes test video - no bars!
I'm flat! I had already come to terms with a repair!
Many many thanks!
* is relieved *
Greeting Sutt
Antwort von Maik:
Sutter "wrote:
Hi Maik,
let me briefly consider what I write now ...
Perhaps THANKS?
With pleasure. Glad I could help.
Best regards,
Maik
Antwort von krsek1:
Hello my dears,
had the same problem with a Panasonic NV-MX.
First:
pixelated picture, then 5 horizontal bars with image information, then the black bars, then: black everything.
Open and close and press the bottom of the housing has led me to the fact that I now longer see anything on the display. The time code is not synonymous with running. When he jumps of coils as 3:40:12 to 7:33:20, etc.
The head drum, I've already cleaned with Alc + Q-Tips.
If you have to disassemble the thing. Where do you find the right description?
Or is there an alternative to emergency surgery?
Thanks for any tip!
Solidary greeting Mario
Antwort von Maik:
"krsek1" wrote:
The head drum, I've already cleaned with Alc + Q-Tips.
This was not such a good idea ... You are likely to break more often than anything else.
Quote:
If you have to disassemble the thing. Where do you find the right description?