safer area for 16:9 (1024x576) for plasma / lcd display
Frage von gwailo: April 2006
Hello. I'm just one image as a dvd presentation, which will operate plasmas s.einem messestand to 16:9. now the question is: how far can I go to the edge here in my work 1024x576px large file?
Thanks in advance.
Antwort von Acer:
"Gwailo" wrote:
Hello. I'm just one image as a dvd presentation, which will operate plasmas s.einem messestand to 16:9. now the question is: how far can I go to the edge here in my 1024x576px large arbeitsdate i?
Thanks in advance.
Did you s.den edge of the image? You always have about 5% of the entire surface to release, as television monitors use the so-called "overscan".
Antwort von gwailo:
yes s.rand of the image. I did not know how it is for a modern plasma tv. would then be 5% s.rand. whole or s.jeder page? the heist, I see only 920x520px ca?
Antwort von Acer:
Overall, I cut the monitor (even uncertain whether in plasma or LCD monitors is so, I think so, if net: correct me) off a small portion of the image so that the image detail is reduced. The picture quality is not compromised, your picture should still maintain your top-called format (1024x576)
Antwort von gwailo:
ok, so if this is so, how many pixels the edge should I just leave? It is important, because I have s.rand design elements.
Antwort von Acer:
The overscan area of Television to Television varies. Modern LCD TVs have a lower Overscanbereich as old pipes that belong to the slap. Imagine the video as a Stillimage before that is framed with a picture frame. Some information disappears behind the frame, depending on how large it is. The same applies for TV's synonymous. The Resolutionbleibt the same. In any case, you can * Pi mal Daumen * assess your shots.
Antwort von Markus:
Hello,
make sure that your pictures / Articles will be displayed fully, you ought to s.The general requirements for the dubbing of video tapes to keep (Keyword: Safety Title Area). Then it comes later, not too bad surprises.
Learn More:
Antwort von Acer:
"Markus" wrote:
Hello,
make sure that your pictures / Articles will be displayed fully, you ought to s.The general requirements for the dubbing of video tapes to keep (Keyword: Safety Title Area). Then it comes later, not too bad surprises.
This can net all the programs, my Avid can do what I was Positv surprised.
Antwort von Acer:
Oh yes, Mark, the with the photo frame of you, I'm: so you're wondering net 'lol *
Antwort von Markus:
"Acer" wrote:
Oh yes, Mark, the with the photo frame of you, I'm: so you're wondering net 'lol *
I had thought it to me ... ;-)
Antwort von mario72:
So in our plasma (Panasonic), you can select the image by itself. Thus both a overscan display as one synonymous vollstöndige image display is possible.
hs
Antwort von Acer:
Aha! I know solxche net
Antwort von Markus:
"hs" wrote:
So in our plasma (Panasonic), you can select the image by itself.
Which model is it possible? Or do not you play the video of a DVD player, but to a computer of an existing VGA connection?
Antwort von PowerMac:
LCDs and plasmas have no overscan.
Especially, many LCD TVs are even the native PAL resolution.
Which I have seen so far, had none. Also hardly possible if the panel's native 720x576 full Resolutionvon actuates.
Annoys me, this area. I'm in a TV Magazine that produces synonymous for the Web. What's in the overscan, it ignores the Kadrage so often. Here, I pay attention on it. Unfortunately, the actual DV goes beyond the viewfinder / monitor. So no chance. But there is one of the 40,000 spectators would think less important than a few hundred on the Internet. A meaningful Kadrage and camera work is as impossible.
