Frage von labac:
Hello
I have the new 2006/2007 Plus Magix bought. I installed it and so far everything ok.
Now if I herumschneide s.einem video or try, then turn on the PC just starting. That's all.
What could that be?
Habe
Windows XP SP2
AMD Athlon XP 2200 +
768MB Ram
and 80GB hard drive
That should actually be ok.
Who can help me next?
Thanks in advance
Antwort von steveb:
Do you receive any error messages before? Please check your CPU temperature during times of labor. How then does the IRQ from a situation? Use once synonymous test program to another for editing.
Antwort von labac:
how can I check the temperature during the operation, then?
what does this mean with the IRQ situation? do not understand it completely?
Antwort von steveb:
Have you synonymous with other programs that crash problem?
Antwort von labac:
yes, I have. had a problem when I tried to open my email program.
Antwort von steveb:
I will not complain ... but yes some more infos would be very helpful. In particular, how often crashes the calculator what you have already tried, etc. ... Apparently, it had to do anything with the program for editing.
Antwort von labac:
I had this problem already. But this is even longer ago. And only once or twice occurred.
at vdl it is quite extreme. can really do as good as nothing. Suddenly I wanted to load a small movie => pc from
I wanted to insert images that were synonymous. Then I clicked on the photo to edit it a little too => Pc from
no preference what I want to do with vdl, the pc goes immediately
you need more infos?
Antwort von Dj Dino:
Your calculator does seem generally not to be stable, as editing programs may require the calculator properly, it is no wonder that he makes zicken nochmehr since then.
I commend you on the basis of this article I go through the possible Stabiliätsursachen:
Is comprehensive but complex = Complex Calculator Ursachen.Fange since s.besten with the s.einfachsten to the test cases.
Temperatures are testing you hereby zb quite well:
http://www.chip.de/downloads/c1_downloads_13012871.html
in the program folder, then under Computer-> Sensors-> temperature-> CPU.Bei some BIOSes is the default setting, the PC is off at a certain safe, high CPU temp.
Everything below ~ 65 degrees is usually harmless but synonymous with the CPU type dependent.
That your computer suddenly turns off even suggests may indicate a problem with the power supply in my article you will find references to synonymous zb (allowed voltage fluctuations). With "Everest" because you can, incidentally synonymous equal voltage values tested under Computer-> Sensors - > Spannungswerte.Generell is a spontaneous switch off the PC's usually a hardware problem, or even failure.
Good luck.
Antwort von Dj Dino:
I commend you on the basis of this article I go through the possible Stabiliätsursachen:
http://members.chello.at/djdino/temp/instabil_hilfe.pdf
(Link forget ...)
Antwort von labac:
SUPER! thanks, will check tonight same time everything and then report next. the power supply is not new .. was supposed to be ok.
Antwort von Dj Dino:
If the problem with the previous, old power supply had not yet or not so extreme, it can still possibly be related to a voltage test values are as 100% security.
Betriebsystemseitige causes you test s.besten with the event viewer of XP: http://www.pc-experience.de/wbb2/thread.php?threadid=9114&sid = zb, where to start with the (folder) of choice for
"System"more info "System"
Can be considered synonymous, but the hardware-problems must lead to mistakes which the Event Viewer may be misinterpreted. (May be more likely describes only the effect of a hardware failure problem), then
So first the better schaun the hardware (CPU temp, power supply, defective or in the BIOS, perhaps too quickly adjustable fastening device, etc.) in order ist.Dann rumdoktern only s.OS.
Unfortunately has to go now ...
Antwort von prem:
yes, this problem is really only so extreme, since I use this power supply. It'll go check. because if I vistas;)
Antwort von labac:
So, yesterday I downloaded and installed this everlast. strangely, it worked fine yesterday!! I was finally able to work with vdl! But I Ahbe really nothing else like this program been installed on the side and had to check my cpu temperature too, which was always between 36 and 38 °.
I hope the problem is now solved.
THANK YOU
