Infoseite // Tripod head screw (screw head in order to fix!)



Frage von Blackeagle123:


Hi,

Some tripod heads have 1-3 small screws, one of the turns down to the tripod head so that it does not help solve pan.

The question is: When Manfrotto heads I still have not seen this since even these "ribs" down turn have.

What have the heads? Is there a standard? What is the distance of the center?

Should we therefore be careful when Purchase a tripod?

Greetings!

Space


Antwort von beiti:

I know the only of Manfrotto (and identical or replicas). The top of the stand contains the set screws, the head is balanced by the ribs.

Space


Antwort von gast3:

s.den synonymous of the Manfrotto know ........ ribs prevent s.Boden of the head set screws twisting of the tripod head, of course, better than flat s.einer Fläche.Der tripod plate of most Manfrottostative has 3 set screws.

Space


Antwort von Blackeagle123:

Hey,

yes, just so I know the synonymous. But it seems synonymous to give a few other tripod heads.



Space


Antwort von domain:

The Giotto Tripods are synonymous, the three set screws. But I have the same views reingedreht so far that they no longer disturb the From-and screw the video head. Pretty useless accessory :-)
Of course you can fit on every head of every Tripod, if only the central standard screw fit.

Space


Antwort von Blackeagle123:

Well, if you have such a Bilora-head, would probably loosen up on the standard 3 / 8 inch screw again and again, if you do not have the right "locking" screw, right?

Greetings!

Space


Antwort von gast3:

yes, if you forget the link pivoting to solve the friction .... or really cold, is the outer turning the cog .... even make sense, however, who must constantly change the video head against a zBKugelkopf (Photography) is the Geschraube the most annoying!

Space


Antwort von Blackeagle123:

Sure, one can omit the screw!

Now the question: How far is because of the screw removed in the middle of the Bilora?

Greetings!

Space


Antwort von gast3:

times fundamental: That which you here (refer to the figure) as a head, the tripod plate, dhdie support surface for the Statvkopf!
On the tripod head is the camera.de tripod head to the central threaded bore no other thread or has holes on its bottom!

The grub screws for the fixation of this head are in the tripod plate, after placing the head on the plate by means of a central 1 / 4 "or 3 / 8" screw, security against loosening of this connection, the set screws of the bottom to the head screwed, the spacing of these bolts from the center is no preference, physically seen each next out, the better, the lower support surface of the tripod head, it is taken to disconnect () and, depending on the Manufacturer of different sizes. (the same applies to the surface of the tripod plate )

Space



Space


Antwort von Blackeagle123:

Hey,

thanks for the explanation, to me is anything but clear! And there are Bilora HEADS, which have a bore with a thread, so you can freeze the head.

Now the only question to be removed as far from the edge of the hole in the plate must, so you can attach a Bilora head is!? (For a quasi-yourself a plate)

Greetings!

Space





slashCAM nutzt Cookies zur Optimierung des Angebots, auch Cookies Dritter. Die Speicherung von Cookies kann in den Browsereinstellungen unterbunden werden. Mehr Informationen erhalten Sie in unserer Datenschutzerklärung. Mehr Infos Verstanden!
RSS Suche YouTube Facebook Twitter slashCAM-Slash