Frage von teilo72:
Hello,
as the title suggests, I have digitized 16:9 material with Adobe Premiere Pro.
Unfortunately, I've created a 4:3 Project.
Movie I have already finished and have it play only when I noticed that screwed up.
Has anyone a trick I like the whole can still be saved??
Thank you very much
Antwort von hsp:
cut again?
Antwort von beiti:
What speaks against it, switch to the project settings to 16:9?
Antwort von Markus:
cut again? No need. The Resolutionbei 4:3 - and 16:9 images is absolutely identical, so you can outsmart synonymous to poverty, without compromising image quality. - But to do that only if Beitis proposal does not help. ;-)
Antwort von hsp:
ne easily create a mask in photo shop or any other image editing program is s.besten when a 16:9 image captured and then just the beam or the image will auschneidet with blue (255) then completes the cut and transfer program with the bluescreen key punching of the Blue I now tell me so and then submit the video I've already made so zb evt gehts synonymous easier or anderst :-)
Antwort von Markus:
ne simple mask in photo shop or any other image editing program to create ... I've read a few times, your proposal now, but I'm still not entirely clear what you really want out ...?!
Antwort von hsp:
na on the 4:3 image, the beam simply put?
or when I do something fundamental wrong?
Antwort von Markus:
Fundamentally, perhaps, but there are easier ways than any relatively idle time Blue boxing:
1) You could picture regarding the issue with the Crop Crop function without scaling it again. Then cut away the top and bottom edges were simply black.
2) Or you can submit a Photoshop mask over it, the two black bars and in the middle of a transparent area shows. There then runs the video and if you can still adjust the picture (slide the video image behind the mask up or down).
I would not turn in this case, however, the 4:3-letterbox 16:9 material, because it remains the fact remains 4:3, but that one still sees less. ;-)
Antwort von hsp:
ok then explain to me how one time a mask with a ps transperenter should save so that the surface area synonymous with premiere've always known I will be saved in the jpg format when it detects the surface but net as transparent habs done wrong or I may of course be synonymous
Antwort von hsp:
of the letterbox is to me synonymous with clear :-) But yes evt is the net so bad if it only is supposed to be effeckt :-)
Antwort von beiti:
I do not understand the problem completely. Although I myself still Premiere 6.0, but the fundamentals would have not changed in PP:
The project settings (project templates) refer to the output format, the behavior on capture, they have no influence. Captured is always what is on the tape, whether it be 4:3 or 16:9, PAL or NTSC.
If the default format, but differs from the recorded material, it will be converted before output (as you noticed s.den long render times).
As a remedy, it should be sufficient in this case, adjust the "Project> Project Settings> Video Filters" is the correct pixel aspect ratio of the output, that is 1:1,422 for 16:9 widescreen material. Then comes a warning that delete the preview files.
What happens with songs that have been created under the 4:3-default, they would have to try (either pulled or reduced in width).
The actual video footage in any case remain intact.
Antwort von hsp:
ok then everything is clear!
Antwort von Markus:
... I've always be saved in the jpg format because it recognizes the surface but net as transparent ... No wonder, because the JPEG format does not support transparency. Save the picture instead of the Photoshop PSD format.
What happens with titles that have been created under the 4:3-default, you should try ... Tracks, which are in a 4:3-Project and then investing in a 16:9 project imported, they are breitgezogen. Before that, there is a communication of Premiere.
