[17:46 Tue,29.July 2025 by Thomas Richter] |
Canon has released new firmware for two of its Cinema EOS cameras (C80 and C400) and several EOS R system cameras (including the R1, R5, R5 II, and R5 C). All updates have a new feature in common: the ability to protect the camera with a 6-digit PIN, which can be set when the camera is first restarted after the firmware update. The PIN entry is then required each time the camera is turned on, but can also be deactivated. This feature has also been added to the EOS R6 Mark II, EOS R7, EOS R8, EOS R10, EOS R50, and EOS R50 V. ![]() Canon EOS C400
The Canon EOS C400 and EOS C80 also receive support for the correction of distortion and chromatic aberration when playing Cinema RAW Light clips in the camera. In addition, CV protocols can be output to multiple devices for virtual productions. Lens metadata can then be used by multiple different computers running the Canon CV Metadata Extraction Plugin. With the new firmware version, the edge display (display level 2) is also expanded on both cameras to display more information at a glance. This includes parameters for sensor mode and resolution, recording codec selected for each card slot, custom image gamma and color space, digital image stabilization status, and electronic level tilt angle. The firmware update for the Canon EOS R1 and R5 II is almost a double one, because the version released shortly before had caused a serious new problem and had to be withdrawn. The problem (videos could not be recorded correctly when a memory card with more than 2 TB was used and the "Pre-Recording" setting was activated) has now been fixed in the very latest firmware. ![]() Canon EOS C80 Canon EOS C80The ![]() 1. Improved security features. A password must first be set. - Adds the ability to review the history of changes to passwords, network information, or other settings. 2. Allows firmware updates to be performed when the camera is connected to the Internet and new firmware is made available on Canon servers. 3. Adds support for the following transmission methods in the CV protocol: - Broadcast - Multicast (same segment only) 4. Allows RAW clips to be played back in media mode with lens correction such as distortion aberration correction. 5. Allows the following information to be displayed for[DISP level 2]. - Recording format / Main resolution / Sensor mode / Digital IS / Gamma/Color space level (numeric) 6. Changes the behavior of an assignable button when[Pause Digital IS] is set: The function is switched on/off each time it is pressed, instead of just pausing when the button is pressed. ![]() Canon EOS C400 Canon EOS C400The ![]() 1. Improved security features. A password must first be set. • Adds the ability to review the history of changes to passwords, network information, or other settings. 2. Allows firmware updates to be performed when the camera is connected to the Internet and new firmware is made available on Canon servers. 3. Supports the following transmission methods in the CV protocol: - Broadcast - Multicast (same segment only) 4. Allows RAW clips to be played back in media mode with lens correction such as distortion aberration correction. 5. Adds the[Track after Focusing] function. 6. Allows the following information to be displayed for[DISP level 2]. Recording format / Main resolution / Sensor mode / Digital IS / Gamma/Color space Level (Numeric) 7. Switches "On/Off" each time the button is pressed when the[Pause Digital IS] function is used, instead of just pausing while the button is pressed, to improve usability. 8. Fixes minor issues. ![]() Canon EOS R1 Canon EOS R1This ![]() 1. Fixes an issue where videos could not be recorded correctly when a memory card with more than 2 TB was used and the[Pre-recording] setting was enabled. 2. Fixes an issue where the camera did not function properly after updating to firmware version 1.1.0 when the photo shooting/video recording switching function was set to[Silent Shutter Function Switching] or[Disable]. This firmware also includes the following changes introduced in firmware version 1.1.0: 1. Improved security features. A password must first be set. - Adds the ability to review the history of changes to passwords, network information, or other settings. 2. Allows firmware updates to be performed when the camera is connected to the Internet and new firmware is made available on Canon servers. 3. Adds[Viewfinder Priority] mode, which activates the viewfinder when a user is detected by the rear sensor. 4. Provides the ability to automatically detect flicker at 100 or 120 Hz during live view display. 5. Adds the ability to register the focus position as a preset in the CR-A100 Camera Remote Application. This capability makes it easier to focus on objects at the desired distance when the application is used with the Robotic Camera System CR-S700R. 6. Adds the ability to select[Panning Assist]. When users pan with compatible lenses, image stabilization and corrections for blurred subjects during exposure are applied. 7. Provides the ability to select[Case Special] to extend servo AF characteristics, which is effective for subjects behind a net at sporting events such as badminton or volleyball. 8. Adds support for the Software Development Assistance Kit (EDSDK/CCAPI). 9. Adds a function that simultaneously protects images when they are rated. 10. Adds the ability to use up to 8 TB CFexpress cards. Note – Cards larger than 8 TB require low-level formatting by the camera. – Cards larger than 8 TB are treated as 8 TB cards. – Cards larger than 2 TB cannot be used to update the firmware. 11. Provides a lower image capture rate to avoid overheating during extended remote shooting when connected to the CR-A100. 12. When transferring images with voice memos via FTP, the priority of the transfer order has now changed, with the voice memo file (WAV) being sent first and then the image file. If a voice memo is added to an image in the queue for transfer, the image and voice memo are now sent last. 13. Adds the ability to set the number of shots taken in continuous shooting mode. 14. Adds the ability to set[Airplane mode] to the customization of the recording button. 15. Adds the ability to enable[Exposure Simulation] when a flash unit is connected. 16. Improved AF tracking during video recording for subjects that are difficult to focus on. 17. Fixes an issue where Err70 may occur when an image is magnified after shooting when[Blackout-Free Display] is set to "On" and[Servo 1st image priority/One-Shot AF release priority] is set to "Release priority". 18. Fixes an issue where Err70 may occur during Bluetooth communication due to interference from other Bluetooth devices. 19. Fixes an issue where Err70 may occur during repeated shooting in "High-speed continuous shooting +)" mode. 20. Fixes an issue where Err70 may occur when shooting with electronic shutter immediately after startup. 21. Fixes an issue where Err70 may occur during video recording in "FHD239.8P/200.0P". 22. Fixes an issue where Error 70 may occur when filming in video mode when the frame rate is set to "50.00P" and[Movie Digital IS] is set to "On" or "Enhanced". 23. Fixes an issue where Err70 may occur during recording when both[Pre-recording] and[Auto send] to image.canon are set to "Enable". 24. Fixes an issue where the camera may stop functioning properly when[Image Review] is set to "Off" and the monitor switches to low brightness mode after continuous shooting. 25. Fixes an issue where video recording is not possible when remote live view shooting is used in EOS Utility during output via HDMI. 26. Fixes an issue where large RAW image files may not be transferred via Camera Connect. 27. Fixes an issue where the camera may not connect to Wi-Fi 7-compatible routers. ![]() Canon EOS R5 Canon EOS R5The ![]() 1. Improved security features. A password must first be set. - Adds the ability to review the history of changes to passwords, network information, or other settings. 2. Allows firmware updates to be performed when the camera is connected to the Internet and new firmware is made available on Canon servers. 3. Adds support for the Software Development Assistance Kit (EDSDK/CCAPI). 4. Adds a function that simultaneously protects images when they are rated. 5. Adds the ability to use up to 8 TB CFexpress cards. Note - Cards larger than 8 TB require low-level formatting by the camera. - Cards larger than 8 TB are treated as 8 TB cards. - Cards larger than 2 TB cannot be used to update the firmware. 6. Adds compatibility for peripheral coordinated control with the RF16-28mm F2.8 IS STM lens. - With RF16-28mm F2.8 IST STM, peripheral coordinated control is only applied when shooting photos. 7. Fixes an issue where Err70 may occur during Bluetooth communication due to interference from other Bluetooth devices. 8. Fixes an issue where Err70 may occur during repeated shooting in "High-speed continuous shooting +)" mode. 9. Fixes an issue where the HDMI output temporarily stops when[Screen Off] is enabled in the power saving settings. ![]() Canon EOS R5 II Canon EOS R5 IIThis ![]() 1. Fixes an issue where videos could not be recorded correctly when a memory card with more than 2 TB was used and the[Pre-recording] setting was enabled. This firmware also includes the following changes introduced in firmware version 1.1.0: 1. Improved security features. A password must first be set. - Adds the ability to review the history of changes to passwords, network information, or other settings. 2. Allows firmware updates to be performed when the camera is connected to the Internet and new firmware is made available on Canon servers. 3. Provides the ability to automatically detect flicker at 100 or 120 Hz during live view display. 4. Adds the ability to register the focus position as a preset in the CR-A100 Camera Remote Application. This capability makes it easier to focus on objects at the desired distance when the application is used with the Robotic Camera System CR-S700R. 5. Provides the ability to select[Case Special] to extend servo AF characteristics, which is effective for subjects behind a net at sporting events such as badminton or volleyball. 6. Adds support for the Software Development Assistance Kit (EDSDK/CCAPI). 7. Adds a function that simultaneously protects images when they are rated. 8. Improves image stabilization control for lenses compatible with peripheral coordinated control. 9. Adds support for the Software Development Assistance Kit (EDSDK/CCAPI). 10. Provides a lower image capture rate to avoid overheating during extended remote shooting when connected to the CR-A100. 11. When transferring images with voice memos via FTP, the priority of the transfer order has now changed, with the voice memo file (WAV) being sent first and then the image file. If a voice memo is added to an image in the queue for transfer, the image and voice memo are now sent last. 12. Adds the ability to set the number of shots taken in continuous shooting mode. 13. Adds the ability to set[Airplane mode] to the customization of the recording button. 14. Adds the ability to enable[Exposure Simulation] when a flash unit is connected. 15. Improved AF tracking during video recording for subjects that are difficult to focus on. 16. Fixes an issue where Err70 may occur when an image is magnified after shooting when[Blackout-Free Display] is set to "On" and[Servo 1st image priority/One-Shot AF release priority] is set to "Release priority". 17. Fixes an issue where Err70 may occur during Bluetooth communication due to interference from other Bluetooth devices. 18. Fixes an issue where Err70 may occur during repeated shooting in "High-speed continuous shooting +)" mode. 19. Fixes an issue where Err70 may occur when shooting with electronic shutter immediately after startup. 20. Fixes an issue where Err70 may occur during video recording in "FHD239.8P/200.0P". 21. Fixes an issue where Error 70 may occur when filming in video mode when the frame rate is set to "50.00P" and[Movie Digital IS] is set to "On" or "Enhanced". 22. Fixes an issue where Err70 may occur during recording when both[Pre-recording] and[Auto send] to image.canon are set to "Enable". 23. Fixes an issue where the camera may stop functioning properly when[Image Review] is set to "Off" and the monitor switches to low brightness mode after continuous shooting. 24. Fixes an issue where video recording is not possible when remote live view shooting is used in EOS Utility during output via HDMI. 25. Fixes an issue where large RAW image files may not be transferred via Camera Connect. 26. Fixes an issue where a horizontal line is temporarily displayed in the viewfinder. 27. Fixes an issue where the camera may not connect to Wi-Fi 7-compatible routers. ![]() Canon EOS R5 C Canon EOS R5 CThe ![]() 1. Adds a function that simultaneously protects images when they are rated. 2. Improved security features. A password must first be set. -Adds the ability to review the history of changes to passwords, network information, or other settings. 3. Allows firmware updates to be performed when the camera is connected to the Internet and new firmware is made available on Canon servers. ![]() deutsche Version dieser Seite: Neue Firmware für Canon EOS C80, C400, R1, R5, R5 II und R5 C verfügbar |
![]() |