Infoseite // Premiere CS 3 - Canon XH A1 - HD Capture Problem milk - to the mice; (



Frage von spitzfindig:


Hello SC community

Although I know that this problem has been acknowledged many times, but I was none of the previous answers to help.

It is annoying!

I can capture in HD recorded material is not easy with Premiere CS3 (and this is no preference which mode, 25F, i, etc).
But, in DV mode, the capture goes without problems!

It appears the following message:
Recorder can not be activated and should be reset

I have installed the following package (Progressive plugin):
http://www.adobe.com/support/downloads/thankyou.jsp?ftpID=3408&fileID=3205

Also in my Premiere CS3 or a folder with the project settings 'HDV'.

None of the presets work with the capture.
My next step to peace of mind then was to try out your recommended HDVSplit. 've Got it installed and gone through the instructions. However, it is synonymous not recognize my video camera. On the website of HDVSplit is it written that you isntalleiren the recorders and driver must be behind the following link:
http://hdvforever.com/hdv/hdrhc1/freecapture/default.htm

Now this is no longer current, that is dead

Do you have ne solution or help for me?

Either another HD Capture program or a working solution for my premiere issue?
The Adobe support sends me only the link to the drivers for HDV Premiere .... proving the apparently synonymous not next.

Have you ever thank you in advance,

captious

Space


Antwort von HitschlerGummi:

Same problem as I Ner week.
Worked with the PD170 as gabs never had any problems.
Since I have the FX1 it reports exactly the same.

Space


Antwort von Axel:

I'm not exactly known as a premiere fan. But true fans will premiere set to a hard test when it comes to self gecapturtes HDV. There are old threads on this subject, which with a successful capture is not yet finished, but unfortunately only just beginning (> Image Errors> asynchronous> permanent inconclusive "Indexing"> crash with long clips). Perhaps with the CS5 is history. It was certainly at that time with CS3 story if they had used to capture "HDVsplit. At least it looked that way. The many threads ended with a works ", then was quiet.

Space


Antwort von spitzfindig:

Hi Axel, thank you for your Anntwort ....

And you have an idea why HDVSplit could not recognize my camcorder? Or are points where I can get the device driver for this program?

Thank you!

Space


Antwort von Alf_300:

http://www.kgbird.com/DVHSTool/

Space


Antwort von spitzfindig:

@ Alf_300

Also thank you, but unfortunately the website does not on the howto. The installeirte program looks like a browser and as my camcorder is s.Arbeitsplatz did not appear, bring me the most Nich much - the camcorder was until now solely detected in the editing program, even under XP it before! But perhaps I understand the principle of the program was not as accurate, I click through, thank you!

Space


Antwort von Alf_300:

Then there still the

Panasonic DVHS - AVC Tape Drivers

Space


Antwort von spitzfindig:

Do not believe the hamoniert the Panasonic Drivers with my Canon: D

Hja, I see already the inevitable switch to the Mac ... Since you have already absorbs the ne Cam Hd and usable isses Nich won '.

DigitAll - where should the lead only;)

Space


Antwort von Alf_300:

To believe is to know nothing -;)

for there will still CapDVHS

http://www.yamabe.org/softbody.html#CapDVHS

In short order without end Drivers

The switch to MAC is of course the more optimal solution

Space



Space


Antwort von Axel:

"Alf_300" wrote:
for there will still CapDVHS

http://www.yamabe.org/softbody.html#CapDVHS

In short order without end Drivers
[Color = green: 11864ba945] MPEG2-TS Remux’c [’ <remuxts v0.0.2.29 remuxts00229.zip

| ‘l’’’v’ `’’, ¼, ½ ’f [’ ^, ª ³, ¼, o-Í, ³, ê, È, ¢ ZZ, a v Í ufull, É’ ’f’b’n`, ¼, Ä 0 º,³,¢ b

y " Ï x "_ z
e " \ } |, ð 0 POEE " \ <l, É " Ï x
e " IS · ' , Ì 0 æ-Ê, Ì, ¿, ç, Â, ", DOE ¸ ,³,¹,½
e, », Ì '¼ a’o’o’t’b’b’n’x

| Remuxts, Ícapdvhs, Ì u, ¨, Ü, ¯ 0 ’ ¬ ’v’ ’o’ v, È, Ì, Å’t’ | [’g, Í`ú'Ò, ¼, È, ¢, Å, ,¾,³,¢ b [/ color]




This makes you smile.

Space


Antwort von Alf_300:

Gibts there a problem?

First time CapDVHS0306. (English version)

The Panasonic drivers for the way:

Panasonic Digital AV / C Tape Device "
JVC Digital AV / C Tape Device "
Hitachi Digital AV / C Tape Device "
Toshiba Digital AV / C Tape Device "

Space


Antwort von spitzfindig:

the clyphen s.wenigsten bother me, much more synonymous bothers me that this program will recognize my camcorder simply do not ... sigh

Space


Antwort von Alf_300:

Unfortunately, there is again no email or I would send you the Pana Drivers times

Space


Antwort von spitzfindig:

eieiei! yes that would be super;

contact [at] liq-hq.de

Space


Antwort von Alf_300:

En route

Space


Antwort von spitzfindig:

thank you very much! The drivers arrived, but still does not work.
Then I have to rent me a bad way einenn editing suite; (And as fast as possible to make the finances to purchase a Mac ... heiejei ...

thanks

s

Space


Antwort von Alf_300:

This is bad
Have the calculator restarted?

Space


Antwort von spitzfindig:

Jap! The drivers must be copied into the Windows system or?
For driver installation, he says, was not the appropriate one.

Space



Space


Antwort von Alf_300:

The inf and select install right mouse button -

Space


Antwort von Axel:

Again, I do. It's not that the CS3 could not capture. Firewire is just bitchy. I would still check a couple of times the software and device settings and always separate FW before. At least before I would rent an editing suite.

And Schonmal the trial version of Console
And nochwas:
Quote: ch can in HD recorded material with just Premiere CS3 does not capture (and this is no preference which mode, 25F, i, etc).

I did not even premiere, so it can unfortunately not quite say for certain. As always synonymous Project, or sequence settings (such as 1080p for the "f" mode or as loud), the recording-setting may only be simply "HDV" match. I still remember that that was important.


Space


Antwort von Meggs:

You need to capture any Windows Drivers, only one functioning FireWire input. Premiere zickt around sometimes, but HDV Split should always work. Is at least as my XH A1s, on 3 different WinXP PCs of 64 to Win7.
After the capture in DV mode goes well, the A1 is detected synonymous. I would like to see once the settings menu, the A1, instead of installing all kinds of drivers.

Space


Antwort von spitzfindig:

@ Axel; console'll try me once, thank you!

@ Meggs
My FireWire works, as I said at the DV camera is detected, then I check again the Eisntellungen internal in the camera .... I am aware of until now but no errors.

Thank you all for the effort! Will not go too wrong hehe

Space


Antwort von robl21f:

hello ....

Meggs supplement to note: When you change the XHA1 menu (where I am synonymous with the solution to the problem tend) the firewire cable !!!!, deduct previously only then make changes in the menu because otherwise some settings in the menu XHA1 can not do! ! .... sounds funny, but it is so!

my settings in the xha1menü hdv-capture in premiere: (Power Wheel -> VCR ... Menu -> Signal setup)

AV-> DV = off
HD down conv = off

firewire plug in, turn on cam, premiere boot (check settings in the premiere recording-windows, if necessary, before the boot set already) ..... and then it should work

gruss rob

Space


Antwort von Axel:

"Robl21f" wrote: Meggs supplement to note: When you change the XHA1 menu (where I am synonymous with the solution to the problem tend) the firewire cable !!!!, deduct previously only then make changes in the menu because otherwise some settings in the menu XHA1 can not do! ! .... sounds funny, but it is so!

Yeah, I thought synonymous herewith.

"Axel" wrote: I would still check a couple of times the software and device settings and always separate FW before.

"Robl21f" wrote: my settings in the xha1menü hdv-capture in premiere: (Power Wheel -> VCR ... Menu -> Signal setup)

AV-> DV = off
HD down conv = off

firewire plug in, turn on cam, premiere boot (check settings in the premiere recording-windows, if necessary, before the boot set already) ..... and then it should work


Super. subtle: print fits's the same for next time

Space


Antwort von spitzfindig:

hach people .... it was even worse; mitlerweile says Premiere steadfast; The capture device is offline. And despite your many tips.

I think my problem is deeper, somewhere between Betriebsys and Software ... I fear a reinstall of windows is due.

I'll print out the procedure anyway!

Oh me is invaded; it can synonymous with the fact that I have dubbed the tape? Before recordings were on it nu 50i 25f.

The Eisntellung fit together yet:

recording:
HD
25F
1080i/576i

Settings in the VRC Mode:
1080i/576i
AV-DV: Off
HD-down: not selected

and to my Premiere Eisntellungen:
Canon 1080p25 progressive scan HD Anamorp 1080

bb

Space


Antwort von Alf_300:

Before you install new, you should try the Canon Console

Space


Antwort von robl21f:

hello again ....

hd should be down and should be selected to stand out / off .... possible that this attitude still on "downconvertierung" and is therefore one is hdv capture-not possible ... was the cable ????? deducted deducted in the settings important !!!.... or again to reset the cam to factory settings and re-examine these settings

these settings are not ok, it probably will not work with the console synonymous ... and not synonymous with hdv split ... and would justify why it works with dv-capture

subtle, you do not live by chance in münchen / munich room??

gruss rob

Space



Space


Antwort von spitzfindig:

Hi rob,

I do that sometimes with the factory settings ...
No, I'm n.entfernt only to work in Munich and the only synonymous over the weekend - this example - the residence I have over 250.
Wanted to give me some emotional support? :)

Thank you!

Space


Antwort von robl21f:

lol .... psychic does not have tangible .... :-)) .... had suggested with your XHA1 come too soon, then we would have solved this with the settings here and the band once captured ...

gruss rob

Space


Antwort von spitzfindig:

that would be of course have been great! thanks for the offer! But unfortunately, 250 n.sind unfortunately too much at times as just ....

So - Have installed the console again synonymous and your tips (rob) processed - Conclusion: Offline recorder.

I have to think probably so slow s.ne new installation, at least for now Premiere ... hfffffffff

Space


Antwort von Meggs:

"Subtle" wrote:
I think my problem is deeper, somewhere between Betriebsys and Software ... I fear a reinstall of windows is due.


Perhaps the driver installation attempts not so great. Do something, ne times System Restore a few days back.

Space


Antwort von spitzfindig:

"Meggs wrote:
Perhaps the driver installation attempts not so great. Do something, ne times System Restore a few days back.


Hmm, that's synonymous a good chance - I'll try! thx

Space



Antworten zu ähnlichen Fragen //


Canon XH A1 and Adobe Premiere Pro 2.0
Canon XH A1 - capturing not work anymore
Capturingproblem with xh a1
XH A1 trouble capturing material with Final Cut Pro 5
Certain tape for XH A1 and capturing issues!
Settings when capturing with Canon XH A1 at Premiere2Pro




slashCAM nutzt Cookies zur Optimierung des Angebots, auch Cookies Dritter. Die Speicherung von Cookies kann in den Browsereinstellungen unterbunden werden. Mehr Informationen erhalten Sie in unserer Datenschutzerklärung. Mehr Infos Verstanden!
RSS Suche YouTube Facebook Twitter slashCAM-Slash