Frage von ereaser222:
Hello, following problem:
I have a DVD with Studio DV (Pal) is created. Now I want to convert this DVD into NTSC.
I have read that you should create the movie site is available in AVI and Canopus DV with the program of converting PAL to NTSC could. However, there is this program a lot of output options, and I do not know what I should choose. Also I am not sure whether it works at all.
Who can tell me how easily it can convert PAL DVD to NTSC. Studio DV AVI files can create synonymous. However, I do not know whether it can output synonymous Studio DV NTSC files, the AVI capture and s.end than NTSC DVDs.
Possibly yes, it is synonymous Programs (cheap when it comes).
And again, perhaps an Dume question, but I hardly know my way. I can not do the normal blanks which I have gentutzt synonymous for the PAL DVD to take to burn the NTSC version or are there differences?
Antwort von Gast1:
Canopus ProCoder is one of the better / best conversion programs "PAL <NTSC> Add". Thereafter, the same procedure as in a VOB.
Antwort von Gast1:
There is probably what went wrong, so again:
Canopus ProCoder is one of the better / best conversion programs "PAL <-> NTSC.
Copy the *. VOB of your original DVD to the hard drive.
Import it then ProCoder (Source -> Add). If there is more than a VOB, click "Stitch".
As a target you choose "MPEG2 - DVD - NTSC (VOB)" and are converting.
The resulting AUDIO_TS VIDEO_TS and burn you as an ISO (not video DVD) on any old DVD (are) for PAL and NTSC the same.
Antwort von ereaser222:
I can not import, but with Canopus. Vob files. How are you doing this?
Is it the file format which then comes out eg with Studio DV capture and build a menu around this then completely burn to DVD?
Or should I rather the AVI file was already synonymous convert audio files containing?
If I have as output an AVI file with 29.97 frames per second in a size of 720x480 which is NTSC then a File? This I could then use with Studio DV
Antwort von ereaser222:
I have just turned round as AVI 2 file. However, the jerky file. Why is that?
As I said. I do not understand it. If any Studio DV not so clear? Creates the Magix?
Antwort von alfa:
There is probably what went wrong, so again:
Canopus ProCoder is one of the better / best conversion programs "PAL <-> NTSC.
Copy the *. VOB of your original DVD to the hard drive.
Import it then ProCoder (Source -> Add). If there is more than a VOB, click "Stitch".
As a target you choose "MPEG2 - DVD - NTSC (VOB)" and are converting.
The resulting AUDIO_TS VIDEO_TS and burn you as an ISO (not video DVD) on any old DVD (are) for PAL and NTSC the same. have the same problem. I should convert to a customer in the U.S. a PAL DVD to an NTSC DVD ... so far so good. I've synonymous to each coder, and have now been busy hours without a result achieve ...
how they hang together several VOB files?? (the key "stitch" I do not think)
why I can only convert 19 sec no preference where I set the IN and OUT point?
Thanks for your help :-)
Antwort von alfa:
Fastest solution: Purchase your Ulead. Costs around 100 euros. Super program. You first create the movie in Pal. Then you can either Pal DVD capture the program or you create the movie with the Pal files as normal with this program. It is easiest if one already has a Pal DVD. Movie capture and create menu.
The program then converts the files before you burn in Pal to Ntsc. Lasts approximately 50 minutes and a brisk Calculator even his 3-4 hours but the quality is just super.
Will you need only the Ntsc files, then read after you've created Ntsc DVD release them back into the program as files.
