Frage von midiwidi:
I have the problem that Pinnacle Studio 12 of my project, only renders exactly 6190 frames and then thinks it was done (the progress bar at 100%, quite normal without stopping the rendering error). If I as the 1st Part of the project rauslösche (Part 1 = Slideshow, Part 2 = video), is the second part is rendered. However, again only 6190 frames and not until the end.
I have the mpeg2-synonymous data at 3000kbps down. Did nothing, except that the resulting file is smaller. Yet only 6190 frames. Also sharing of extra 20GB on the hard drive has nothing. Same result.
Has anyone of you an idea what's wrong?
A workaround would be the Project in small pieces of 6190 frames to decompose and render individually afterwards with another program to put together. I like that but not much.
Antwort von Bruno Peter:
Maybe you render to a FAT32 hard drive, or did only a part is activated, you have a gap somewhere, or ...
Nöö, renders it with me always ...
Antwort von midiwidi:
The disk is formatted in NTFS. What do you mean with "only a part is activated?
A gap is absent. As I said, if I am a part of the project s.Anfang remove, it still only renders exactly 6190 frames. Then, the end of the file rendered by the time I s.Anfang of the project have rausgelöscht next rear.
Has anyone an idea?
Antwort von midiwidi:
Did None of you any idea what's wrong it?
I slowly devices under time pressure. I have the video ready soon.
I hope someone can help me.
Gruß Markus
Antwort von Bruno Peter:
However, it is s.Deinem system ... otherwise there is no this error somewhere else, maybe you have a synonymous yes umbemerktes installation problem.
If you now have three parts render them to a new timeline, and now lay render what happens then?
Antwort von midiwidi:
Will I try s.Wochenende. I would have three parts but with a different program together.
Antwort von Bruno Peter:
I would like to hold of you like to know whether there with Studio 12 is also ...
Antwort von midiwidi:
There has been synonymous not geklappt.Pinnacle breaks exactly s.der same place ab.Ich hab parts with another program together. I have Pinnacle synonymous times on my desktop PC installiert.Dort happens exactly the same, he is after 6190 frames of expression to be ready.
Antwort von Bruno Peter:
Then a fundamental mistake when you are available, probably the only you can explore. Yesterday I used an HDV project with approximately 120,000 frames without interruption herausgerendert and a Blu-ray is created with no problems at Sony's PS3 makes.
Antwort von UFred:
Turn straight through, had the same problem with 39736 frames. Do you have a solution?
Antwort von Henkie:
Turn straight through, had the same problem with 39736 frames. Do you have a solution? Check it out if the film s.einer body with a certain transitional / hangs on dazzle. Sometimes it helps only those rauszuschmeissen.
regards
Antwort von JörgP:
Hello in the round,
Unfortunately there is no solution, is not synonymous of me, but just a confirmation:
One of Studio 11 acquired Project renders in Studio 12 is only accurate to frame 20714th The enstspricht exactly 13:48 min and exactly the size of a 3.068.987kB produced avi files. The Project, I have decomposed, transitions newly made no preference - it is always at 20714 closing.
That means for me that the fault lies not s.Project but s.der SW or s.einer strange configuration of the HW / SW.
Unfortunately I have no solution. Pinnacle Support still struggling.
Has someone an idea? Thank you.
Antwort von Yerri:
It is indeed usually the time or frame number as the rendering error. Just try s.dieser point the clip a little shorter.
PS. One should always synonymous with the projects of Pinnacle finished version with the one they started (in this case Studio 11).
